American Standard Hot Tub 2425E SERIES User Manual

2425E SERIES  
WHIRLPOOL  
INSTALLATION INSTRUCTIONS  
WILLIAMSBURG  
ELITE 5' x 32"™  
HIGH GLOSS ACRYLIC  
SHOWN LESS ALL FITTINGS  
60  
(1524mm)  
12  
(305mm)  
10-1/4  
(260mm)  
ON/OFF  
SWITCH  
THANK YOU...  
for selecting an American Standard bath. Your new  
bath is shipped to you after careful inspection. The  
whirlpool version is completely assembled with pump,  
motor, and system piping. All you need to finish the  
3/4  
(19mm)  
HEATER  
BLANK  
FINISHED  
WALL  
SEE FITTING  
SPECS FOR  
DIMENSIONS  
9
(229 mm)  
installation are your selected fittings and electrical  
connections for a whirlpool.  
PROVIDE ACCESS  
TO PUMP FOR  
SERVICE ON ALL  
INSTALLATIONS  
PUMP  
32  
(813mm)  
16  
(406mm)  
CUTOUT IN FLOOR FOR DRAIN  
To insure maximum performance and pleasure from  
this product, please follow the instructions and  
cautions.  
C/L OF  
SUPPLIES  
3
(8) JETS  
(76mm)  
(2) AIR VALVES  
C/L OF  
C/L OF DRAIN  
SHOWER ARM  
List of Optional Components (not included):  
• Flex-Jet Pulse Jet Kit*  
• Flex-Jet Soft Jet Kit*  
FINISHED  
WALL  
OPTIONAL TO  
FINISHED FLOOR  
USUALLY BETWEEN  
65 & 78  
LEVELING  
STRINGER  
NOT FOR  
C/L OF  
VALVES  
• 5 Foot Apron*  
(1651 & 1981mm)  
SUPPORT  
• E-Z-Install Heater*  
C/L OF  
SPOUT  
12  
C/L OF  
OVERFLOW  
3-1/2  
(305mm) OPT.  
2
4
(51mm)  
(89mm)  
(102mm)  
List of Required Components (not included):  
UNDERSIDE  
OF DECK  
• Drain*  
• Bath Filler*  
19-1/2  
(495mm)  
21-1/2  
(546mm)  
IN-LINE HEATER  
REMOVABLE  
BLANK  
ROUGH  
FLOOR  
* see your Home Depot Retailer  
1-1/2 N.P.T.M.  
THREADS  
INTEGRAL  
FEET  
2-3/4  
(70mm)  
1-1/2 O.D.TAILPIECE  
4-5/8  
(117mm)  
List of Required Tools and Supplies:  
GENERAL SPECIFICATIONS FOR 2425E WHIRLPOOL  
Tools  
Supplies  
INSTALLED SIZE  
WEIGHT  
WEIGHT w/WATER  
GAL. TO OVERFLOW  
WHIRLPOOL MIN. OPERATING VOL.  
BATHING WELL AT SUMP  
BATHING WELL AT RIM  
WATER DEPTH TO OVERFLOW  
FLOOR LOADING  
(PROJECTED AREA)  
PTS.  
CUBE (FT3)  
60 x 32 x 21-1/2 (1524 x 813 x 546mm)  
115 Lbs. (52 Kg.)  
• Level  
• Nails  
574 Lbs. (258 Kg.)  
55 Gal. (208 L.)  
45 Gal. (171 L.)  
16-1/4 x 38-1/4 (413 x 972mm)  
26-1/4 x 52-1/2 (667 x 1334mm)  
15 (381mm)  
• Tape Measure  
• Pipe Wrench  
• Slip Joint Pliers  
• Screw Driver  
• Standard  
• Putty  
• Caulking (waterproof)  
• 1 x 3 or 2 x 2  
Stringers  
43 Lbs./Sq.Ft. (208 Kgs./Sq.m)  
• Drop Cloth  
• 15 amp GFI  
Outlet  
• Cement, Plaster,  
Grout  
Woodworking Tools  
• Personal Safety  
Equipment  
20.8  
35.3  
WHIRLPOOL ELECTRICAL SPECIFICATIONS  
PUMP  
1.6 HP, 9.7 AMPS,120V.  
• Caulking Gun  
GENERAL INSTALLATION INFORMATION  
Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your vendor  
immediately.  
After inspection and during installation, protect the bath from construction damage. After installation, and before  
enclosing with wallboard, tile, etc., water test the unit and check for leaks.  
Do not make modifications to the whirlpool system or remove pump from factory mounting. This could adversely affect  
the safety and performance of the whirlpool and void the warranty. Do not handle or move the whirlpool by the pump,  
motor, or piping system.  
Fittings (bath filler, shower arm, etc.) are not provided with the bath and must be ordered separately. Framing and  
enclosing materials are provided by others. Check for availability of optional American Standard wall tiling bead  
(required for recess installations).  
Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth.  
WARNING! Do not lift whirlpool by the piping harness at any time.  
FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.  
© American Standard Inc. 2002  
All product names listed herein are trademarks  
of American Standard Inc. unless otherwise noted.  
752875-100 Rev. D  
 
ELECTRICAL INSTALLATION INSTRUCTIONS  
All wiring must be performed by a licensed electrician in accordance with the national electrical code and all other  
applicable codes.  
WARNING:  
When using electrical products, basic precautions should always be observed, including the following:  
1. DANGER: RISK OF ELECTRIC SHOCK  
Connect only to a circuit protected by a ground-fault circuit interrupter.  
2. Grounding is required. The unit should be installed by a licensed electrician and grounded.  
3. Install to permit access for servicing.  
4. All building materials and wiring should be routed away from the pump body and heater (if equipped).  
The whirlpool should be installed on a 120 vac, 15 amp dedicated circuit. The circuit should be hard-wired from the  
electrical power supply panel. The circuit must be a three (3) wire circuit from the electrical supply panel. A grounded  
neutral wire and a third wire, earth ground, are essential. ADDING THE E-Z-INSTALL HEATER REQUIRES A  
SEPARATE 15 AMP MAXIMUM GFCI CIRCUIT.  
ELECTRICAL INSTALLATION  
SEPARATE  
15 AMP GFCI  
OUTLET  
WHIRLPOOL MOUNTED  
120 VAC  
AIR SWITCH OR  
WALL TIMER  
PUMP/MOTOR  
GND.  
ELECTRICAL DIAGRAM  
READ AND FOLLOW ALL INSTRUCTIONS  
(3)  
752875-100 Rev. D  
 
WIRE SELECTION GUIDE  
Maximum distance from  
fusebox to motor  
The sizes shown on this  
chart are recommendations  
for copper conductors  
only. Always follow  
local and national  
Motor  
Hi Performance  
Rating  
50'  
100'  
120V Power Line  
12 10  
150'  
200'  
1.6  
electrical codes  
12  
8
DRAIN CONNECTION AND SYSTEM TEST  
Using recommended drain opening, connect whirlpool drain to waste line. Tighten all drain joints securely. Check the  
pump couplings and make sure they are hand-tight. Clean the whirlpool and fill with water to a point 2" above the top of  
the highest jet. Recheck the pump couplings and make certain that they are not leaking. (Although the pump couplings  
are factory tightened and inspected, some loosening may have occured during transit.) Make sure the whirlpool is  
connected to the electrical supply and turn the whirlpool on. Check for leaks around all piping connections while the  
whirlpool is running.  
POST INSTALLATION CLEAN-UP  
Remove all construction debris from bath. Tile grout can be removed with a wooden popsicle stick or tongue depressor.  
Do not use wire brushes or any other metal implement on bath surface.  
Post installation clean-up generally can be completed using warm water and liquid dishwashing detergent. Stubborn dirt or  
®
stains may be removed using granular Spic and Span mixed with water.  
Painter's naphtha can be used to remove excess adhesives and/or wet oil-base paint.  
HARSH CHEMICALS SHOULD NEVER BE USED ON ACRYLIC SURFACES.  
Abrasive cleaners must not be used since they will scratch and dull the surface. Dulled areas can be restored by rubbing  
with a white automotive-type polishing compound and waxing with a liquid wax.  
®
(4)  
SPIC AND SPAN IS A REGISTERED TRADEMARK OF PROCTER & GAMBLE  
752875-100 Rev. D  
 

ACCO Brands Laminator H520 User Manual
Adaptec DVD Player AVC 2210 User Manual
Addonics Technologies Computer Drive AEPDDESU User Manual
ADT Security Services Home Security System BHS 4000A User Manual
Aiko Cassette Player CTH3 115 User Manual
AllerAir Air Cleaner 5000 D and DX User Manual
American Standard Hot Tub 7236XXXW User Manual
American Standard Plumbing Product M968641 User Manual
Asus Car Video System PG278Q User Manual
BC Speakers Portable Speaker DE 600 User Manual