American Standard Hot Tub Whirlpool Bathing Pool User Manual

TOWN SQUARE®  
6' x 42"™  
INSTALLATION  
INSTRUCTIONS  
2742.XXXX SERIES WHIRLPOOL / BATHING POOL  
HIGH GLOSS ACRYLIC  
SHOWN LESS ALL FITTINGS  
THANK YOU...  
for selecting an American Standard bath. Your  
new bath is shipped to you after careful  
inspection. The whirlpool version is completely  
assembled with pump, motor, and system  
piping. All you need to finish the installation  
are your selected fittings and electrical  
connections for a whirlpool.  
71-1/2"  
(1816mm)  
4"  
3"  
(76mm)  
(102mm)  
INTEGRAL  
FITTING DECK  
3" X 14"  
35-3/4"  
(908mm)  
13-1/4"  
(337mm)  
C/L OF DRAIN OUTLET  
(76 X 356mm)  
EDGE OF  
FLOOR  
CUTOUT  
To insure maximum performance and pleasure  
from this product, please follow the  
instructions and cautions.  
PROVIDE ACCESS  
TO PUMP FOR  
SERVICE ON ALL  
INSTALLATIONS  
41-3/4"  
(1060mm)  
FLOOR CUTOUT  
5" X 15"  
(127 X 381mm)  
26-3/4  
(679mm)  
List of Optional Components (not included):  
• Safe-T-Heater 9075.120*  
List of Required Components (not included):  
• Drain 1594.170  
• Bath Filler  
3/4"  
(19mm)  
PUMP  
ON/OFF  
SWITCH  
OUTLINE OF CUTOUT  
70" X 40-1/4"  
(1778 X 1022mm)  
SUCTION  
List of Required Tools and Supplies:  
JETS (8)  
SAFE-T-  
HEATER  
REMOVABLE  
BLANK  
Tools  
Supplies  
• Level  
• Nails  
LEVELING STRINGER  
(NOT FOR SUPPORT)  
2"  
(51mm)  
Tape Measure  
• Pipe Wrench  
• Slip Joint Pliers  
• Screw Driver  
• Standard  
• Putty  
C/L OF  
OVERFLOW  
PUMP  
• Caulking (waterproof)  
• 1 x 3 or 2 x 2  
Stringers  
22"  
(559mm)  
• Drop Cloth  
3-1/4"  
(83mm)  
Woodworking Tools • 20 amp GFI Outlet  
20"  
(508mm)  
ROUGH  
FLOOR  
• Cement, Plaster,  
Grout  
• Personal Safety  
Equipment  
• Caulking Gun  
INTEGRAL  
FEET  
SUPPORT  
1-1/2" N.P.T. THREADS  
1-1/2" O.D.TAILPIECE  
GENERAL INSTALLATION INFORMATION  
3"  
(76mm)  
5/8"  
(16mm)  
Carefully uncrate and inspect your new bath for  
any shipping damage. If such damage is found,  
report it to your vendor immediately.  
After inspection and during installation, protect  
the bath from construction damage. After  
installation, and before enclosing with wallboard,  
tile, etc., water test the unit and check for leaks.  
GENERAL SPECIFICATIONS FOR 2742 WHIRLPOOL  
INSTALLED SIZE  
71-1/2 x 41-3/4 x 22 In. (1816 x 1060 x 559mm)  
WEIGHT  
115 Lbs. (52 Kg.)  
690 Lbs. (313 Kg.)  
Do not make modifications to the whirlpool  
system or remove pump from factory mounting.  
This could adversely affect the safety and  
performance of the whirlpool and void the  
warranty. Do not handle or move the whirlpool by  
the pump, motor, or piping system.  
WEIGHT w/WATER  
GAL. TO OVERFLOW  
WHIRLPOOL MIN. OPERATING VOL.  
BATHING WELL AT SUMP  
BATHING WELL AT RIM  
WATER DEPTH TO OVERFLOW  
FLOOR LOADING  
69 Gal. (261 L)  
60 Gal. (227 L)  
41 x 21-1/2 In. (1041 x 546mm)  
62 x 31-1/2 In. (1574 x 800mm)  
14-1/4 In. (362mm)  
33 Lbs./Sq.Ft. (163 Kgs./Sq.m)  
(PROJECTED AREA)  
PTS.  
Fittings (bath filler, shower arm, etc.) are not  
provided with the bath and must be ordered  
separately. Framing and enclosing materials are  
provided by others.  
27.8  
55.7  
CUBE (FT3)  
WHIRLPOOL ELECTRICAL SPECIFICATIONS  
WHIRLPOOL PUMP  
2.1 HP, 14.4 AMPS ,120V.  
Protect all finished surfaces of the whirlpool  
during construction and installation using a drop  
cloth.  
WARNING! Do not lift whirlpool by the piping  
harness at any time.  
FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.  
© AS America Inc. 2009  
753027-100 REV. F  
All product names listed herein are trademarks  
of AS America Inc. unless otherwise noted.  
 
ELECTRICAL INSTALLATION INSTRUCTIONS  
All wiring must be performed by a licensed electrician in accordance with the national electrical code and all other  
applicable codes.  
WARNING:  
When using electrical products, basic precautions should always be observed, including the following:  
1.  
DANGER: RISK OF ELECTRIC SHOCK  
Connect only to a circuit protected by a ground-fault circuit interrupter.  
Grounding is required. The unit should be installed by a licensed electrician and grounded.  
Install to permit access for servicing.  
2.  
3.  
4.  
All building materials and wiring should be routed away from the pump body and heater (if equipped).  
The air massage version should be installed on a 120 vac, 15 amp dedicated circuit. The whirlpool version should be  
installed on a 120 vac, 20 amp dedicated circuit. The combination system requires a 120 vac, 20 amp dedicated circuit  
for the whirlpool pump and a 120 vac, 15 amp dedicated circuit for the air pump. Each circuit must be a three (3) wire  
circuit from the electrical supply panel. A grounded neutral wire and a third wire, earth ground, are essential. ADDING  
THE SAFE-T-HEATER REQUIRES A SEPARATE 15 AMP MAXIMUM GFCI CIRCUIT.  
ELECTRICAL INSTALLATION  
FOR AIR MASSAGE : SEPARATE 15 AMP GFCI OUTLET  
FOR WHIRLPOOL : SEPARATE 20 AMP GFCI OUTLET  
FOR COMBINATION SYSTEMS : SEPARATE 15 AMP GFCI OUTLET  
(AIR PUMP) AND A SEPARATE 20 AMP GFCI OUTLET (WHIRLPOOL PUMP)  
WHIRLPOOL MOUNTED  
120 VAC  
AIR SWITCH OR  
WALL TIMER  
PUMP/MOTOR  
GND.  
ELECTRICAL DIAGRAM  
READ AND FOLLOW ALL INSTRUCTIONS  
(3)  
753027-100 REV. F  
 
WIRE SELECTION GUIDE  
Maximum distance from  
fusebox to motor  
The sizes shown on this  
chart are recommendations  
for copper conductors  
only. Always follow  
local and national  
Motor  
Hi Performance  
Rating  
50'  
100' 150'  
120V Power Line  
10  
200'  
electrical codes  
2.1  
12  
8
8
DRAIN CONNECTION AND SYSTEM TEST  
Using recommended drain opening, connect whirlpool drain to waste line. Tighten all drain joints securely. Check the  
pump couplings and make sure they are hand-tight. Clean the whirlpool and fill with water to a point 2" above the top of  
the highest jet. Recheck the pump couplings and make certain that they are not leaking. (Although the pump couplings  
are factory tightened and inspected, some loosening may have occurred during transit.) Make sure the whirlpool is  
connected to the electrical supply and turn the whirlpool on. Check for leaks around all piping connections while the  
whirlpool is running.  
POST INSTALLATION CLEAN-UP  
Remove all construction debris from bath. Tile grout can be removed with a wooden popsicle stick or tongue depressor.  
Do not use wire brushes or any other metal implement on bath surface.  
Post installation clean-up generally can be completed using warm water and liquid dishwashing detergent. Stubborn dirt or  
®
stains may be removed using granular Spic and Span mixed with water.  
Painter's naphtha can be used to remove excess adhesives and/or wet oil-base paint.  
FEATURES of YOUR NEW AMERICAN STANDARD ACRYLIC BATHTUB  
Your new acrylic bathtub has been molded in the newest plumbing fixture material available today. Acrylics are  
tough durable finishes that are simple and easy to care for.  
The colors have been formulated to match other American Standard fixtures and enhance your choice of  
bathroom decorations. The high gloss surface is resistant to impact and chemicals and will retain its lasting  
luster with proper care and maintenance.  
AFTERCARE and CLEANING  
• Always fill the tub with temperate water. Excessively hot water may cause surface damage  
• Remove bath mat after use and hang to dry. Allowing bath mat to dry in the tub may cause surface damage.  
• Clean after use with a mild liquid household detergent cleaner. Do not use Lestoil, Lysol Disinfectant (spray  
or concentrate), or Lysol Basin, Tub and Tile Cleaner, Windex, Mr. Clean, Dow Disinfectant Bathroom Cleaner,  
or cleaning products in aerosol cans.  
HARSH CHEMICALS SHOULD NEVER BE USED ON ACRYLIC SURFACES.  
• Do not use wire brushes, knives or sharp objects to remove stains, cigarette tar deposits, or other surface  
blemishes.  
• Abrasive cleaners or powders must not be used, since they will dull the surface. If the glossy surface looses  
its sheen, dulled areas can be restored by rubbing with a white "automotive type" polishing compound and  
waxing with a "liquid wax."  
Do not wax areas where you walk or stand.  
• Do not allow nail polish remover, acetone, dry cleaning fluid, paint remover or other solvents to come into  
contact with the surface.  
• Clean the surrounding surface immediately after using caustic drain cleaners.  
• Burning cigarettes will damage the surface.  
• Should damage to the fixture occur, repairs can be made quickly and easily.  
Your distributor or builder can provide details.  
* For Air Massage and Combination systems, please refer to the Installation and Operating Manual for Air Massage and  
Combination Systems (P/N 753036-100) for additional information.  
®
(4)  
SPIC AND SPAN IS A REGISTERED TRADEMARK OF PROCTER & GAMBLE  
753027-100 REV. F  
 

ADTRAN Network Router 1202890E1 User Manual
ADTRAN Network Router Express L15 User Manual
AEG Refrigerator S75578KG3 User Manual
Air King Electric Heater 1DKX3 8900 User Manual
Alpine Car Video System 68 00493Z15 B User Manual
Alpine GPS Receiver INE NAV 40 User Manual
Altec Lansing Portable Speaker 418 8H User Manual
American Standard Plumbing Product 7430801 User Manual
Asus Computer Hardware 90MB0DU0M0AAY0 User Manual
Audiovox Car Stereo System ACC 60 User Manual