American Standard Plumbing Product 4433001 User Manual

Installation  
Instructions  
QUINCE™  
4433.001  
SINGLE CONTROL KITCHEN  
FAUCET WITH CAST SPOUT  
Thank you for selecting American-Standard...  
the benchmark of fine quality for over 100 years.  
To ensure that your installation proceeds smoothly--  
please read these instructions carefully before you begin.  
Certified to comply with ANSI A112.18.1M  
M965115_Rev.1.1  
Recommended tools  
Phillips Screwdriver  
Adjustable Wrench  
Regular Screwdriver  
Plumbers' Putty or Caulking  
Turn off hot and cold water  
supplies before beginning.  
INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON  
CAUTION  
1
Make certain the SEAL (9) is properly seated in recess of spout base.  
(A) Installation with ESCUTCHEON (1). Apply a bead of putty to bottom edge of ESCUTCHEON with PUTTY PLATE (1).  
Insert supply HOSES (2) and SHANK (3) through hole of ESCUTCHEON with PUTTY PLATE (1) and mounting surface.  
Follow mounting instructions below to secure faucet to mounting surface.  
(B) Installation less ESCUTCHEON (1). Insert all HOSES (2) and SHANK (3) through MOUNTING RING (10) and  
mounting surface. Do not use putty.  
Assemble RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6) onto SHANK (3) from underside  
of sink or mounting surface. Hand tighten LOCKNUT (6) and check that rotation of HANDLE (7) from HOT to COLD  
is centered.  
Use a screwdriver to tighten SCREWS (8) on LOCKNUT (6). Work your way around LOCKNUT (6), tightening  
the screws slightly each time until all are snug to ensure even pressure.  
7
7
A
B
9
10  
9
1
3
2
PUTTY  
2
8
3
SINK OR  
MOUNTING  
SURFACE  
4
5
4
5
8
6
6
 
SERVICE  
5
Reduced flow. If the flow gradually reduces over a number of months, the AERATOR (12) may have collected debris.  
To clean, remove AERATOR (12) and rinse with water and remove any debris. Turn on faucet to wash any debris  
out of the faucet. Thread AERATOR (12) back into spout. Operate faucet.  
Spout leakage. If fitting leaks above or below SPOUT HUB remove SPOUT as follows  
and check SPOUT O-RINGS. First turn off water supply.  
Remove HANDLE BUTTON (2) and loosen SET SCREW (1) with 2.5mm HEX  
WRENCH (11) supplied. Pull HANDLE (3) off valve stem.  
3
1
Pull off CAP (4). Loosen CARTRIDGE SCREWS (5) and remove CARTRIDGE (6).  
2
Remove SPOUT (7) by pulling up gently while moving SPOUT (7) side to side.  
11  
4
5
Check both SPOUT O-RINGS (8) for damage. Replace if necessary.  
On models with SPRAYS, DIVERTER (9) can be cleaned by pulling  
DIVERTER (9) out of the MANIFOLD (10). Rinse clean the DIVERTER (9)  
and MANIFOLD (10). Push DIVERTER (9) back into MANIFOLD (10).  
Reverse procedure to reinstall SPOUT, CARTRIDGE and HANDLE.  
6
Clogged CARTRIDGE outlets or inlets may cause reduced flow.  
To clean, first turn off water supply then:  
13  
Remove PLUG BUTTON (2), loosen HANDLE SCREW (1) and  
remove HANDLE (3).  
Remove ESCUTCHEON CAP (4). Unscrew the three CARTRIDGE  
SCREWS (5). Clean MANIFOLD (10), CARTRIDGE (6) ports and  
SEALS (13).  
SPOUT  
HUB  
7
Clean inlets of CARTRIDGE (6) and MANIFOLD (10).  
12  
Reassemble CARTRIDGE (6), alternately tightening SCREWS (5).  
Replace CAP (4) and HANDLE (3). Check flow.  
10  
8
9
CARE INSTRUCTIONS:  
6
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.  
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A  
CLOTH WITH A COARSE SURFACE.  
M965115_Rev.1.1  
 

AB Soft Battery Charger XS 25000 User Manual
Acer Laptop ZY5 User Manual
Acomdatacom Personal Computer The Executive User Manual
Aiphone Telephone TB 10M User Manual
Air King Ventilation Hood EWF 180 User Manual
Alvin Patio Furniture DC888 User Manual
Amana Clothes Dryer W10562495A User Manual
Asus Network Card P5LD2 User Manual
BC Speakers Speaker 18 RXB User Manual
Behringer Car Amplifier BX108 User Manual