Speed Connect™ Drain
Troubleshooting Guide
If sink does not hold water even though Stopper is in the “down” position:
• Follow CABLE ADJUSTMENT PROCEDURE.
If Stopper does not raise up fully or sink drains too slowly:
• Follow CABLE ADJUSTMENT PROCEDURE.
If you need to remove the Stopper:
• Follow STOPPER REMOVAL PROCEDURE.
If you would like the ability to remove your Stopper simply by lifting it out of the drain:
• Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
CABLE ADJUSTMENT PROCEDURE
Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.
Look at the area on the Drain Body where the Cable was attached and locate the component labeled as
“Cam” in the illustration. Fig. B.
Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go. At this point the
Stopper should be in the UP position. Fig. B, C.
Push DOWN on the Lift-Knob to make sure it is fully down. Fig. C.
Re-attach the Cable to the Drain Body Connection (2) by threading the Cable Connector (1) clockwise onto the
Drain Body Connection (2) and hand-tighten. Fig. A.
DOWN
Fig. A.
Fig. B. Fig. C.
CAM
1
1
RE-ATTACH
CAM CAP
STOPPER
DISCONNECT
2
STOPPER REMOVAL PROCEDURE
Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.
Look at the area on the Drain Body where the Cable was attached and locate the component labeled
as “Cam” and “Cam Cap” in the illustration. Fig. B.
Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain. Fig. D.
Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal. Fig. E.
The Stopper can now be removed by lifting it out of the Drain. Fig. F.
Fig. F.
Fig. D.
Fig. E.
REMOVE
CAM
REMOVE
CAM CAP
51314 Rev.1.3
5
Single Control Lavatory Faucet
with Pop-up Drain
023529-0070A
CARTRIDGE KIT
MODEL NUMBERS
3808.101
M962527-YYY0A
POP-UP ROD
066124-YYYOA
DECORATIVE RING
909719-YYY0A
066070-YYY0A
AERATOR
SPOUT ESCUTCHEON
060275-YYY0A
HANDLE ASSEMBLY
A912699-0070A
RUBBER RING
030746-0020A
HANDLE SCREW KIT
A907086-YYY0A
ESCUTCHEON CAP
M962541-0070A
MOUNTING KIT
023527-0070A
CARTRIDGE SCREWS
060277-YYYOA
ESCUTCHEON KIT
Replace the "YYY" with
appropriate finish code
M962544-YYY0A
CHROME
WHITE
WHITE/CHROME
WHITE/POL. BRASS
BLACK NICKEL/BRASS MIX (PVD)
BLACK SMITH (PVD)
POLISHED BRASS
SATIN (PVD)/CHROME
SATIN NICKEL
002
020
025
028
062
078
099
221
295
297
299
066116-YYY0A
STOPPER
DRAIN STOPPER
ASSEMBLY
066117-YYY0A
2" FLANGE KIT
M953450-YYY0A
COMPLETE
DRAIN ASSEMBLY
M952430-0070A
CABLE ASSEMBLY
060276-YYY0A
LIFT ROD
072574-0070A
EXTENSION ROD
M962457-YYYOA
FLANGE ASSEMBLY
066118-0070A
PIVOT ROD KIT
SATIN BRASS (PVD)
CHROME/POL BRASS
M922872-0070A
CAM SEAT INSERT
M962430-0070A
070847-0070A
CAM ASSEMBLY
CLIP
M952425-YYY0A
DRAIN ASSEMBLY
M961711-0070A
TAILPIECE INSERT
M913207-0070A
TAILPIECE INSERT
070532-0040A
TAILPIECE
M919660-0020A
POP-UP DRAIN ASSEMBLY
BEFORE 01/07
6” TAILPIECE
(NOT INCLUDED
WITH FAUCET)
A919661-0020A
TAILPIECE
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1-800-442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-12-00
M962458-0070A
DRAIN MOUNTING KIT
Product names listed herein are trademarks of American Standard Inc.
©
AS America, Inc. 2008
51314 Rev.1.3
7
|